Menu toggle

Very quiet on here given we are in lockdown!

daviespaj

daviespaj

PCGB Member
Member
3DD67102CB244FEDAEF69D71A67096B8.jpg

Ok, I haven't had much spare time as I am working from home, but did manage to finally get the engine and gearbox mounted on to stands for cleaning and refurbishment. Getting the engine though a single door into my workshop from the garage proved a little tight. Unbolting the inlet manifold and rotating the engine did the trick. I will do a whole lot of cleaning and strip the engine accessories off ready for a rebuild. Probably will use Ninemeister for the rebuild? I did consider trying to rebuild it myself (I am an engineer and have done a number of 'normal' engines in the past). However the Porsche engine is not quite like most standard engines and I could cause a whole heap of trouble if I get it wrong!




 
I did purchase one of the books on rebuilding a Porsche engine, it is essentially based around the 3.2 engine rather than the 964 3.6 engine. I guess much is the same, but it's the inside knowledge a specialist would have on this particular engine especially around oil leak prevention (particular problem on the early generation engine). I am still a little on the fence, let's see how the strip down goes? Can't cross any threads while taking it apart (lol)!
Cheers
Peter
 
I understand that the original 964's didn't use a head gasket which in 80% of the cases was OK.
However those 20% suffered excessive oil loss and had rebuilds where a recess was machined in the cylinder head to allow a gasket to be installed. I think my C2 was one of those as it was registered 23/10/89 and had a rebuild at 50k.
 
Interesting comments, I was told that in order to fit the later head gasket you had to change the cylinder barrels to the later type? This is why I feel uncertain about having a go myself, what are the various bits and pieces that need to be changed or modified other than bearings, rings etc? Although the engine has completed almost 180k miles it ran well but leaked oil like a tanker on the rocks.
 
Early engines were built without a cylinder head gasket, and in a small percentage of engines, can leak. Porsche fixed those that were found leaking at that time, with leaking being defined as wet to the touch. In 1991, Porsche updated the production engines by adding a cylinder head gasket, redesigning the cylinder head base, and installing all steel head studs. The 1990-on 964's use a dual mass flywheel, which helps isolate drive-train vibration, however, the early Freudenberg units proved unreliable. In 1992 Porsche changed to LUK-manufactured units, which have stood the test of time. In late 1993, Porsche added a vent kit for the distributor, to help prevent the dual distributor rubber belt from breaking due to ozone concentrations. There is a $10 kit to add this to earlier 964's. 1989-1991 964's need different spacers on the steering rack if you want to fit 17" wheels. In order to store the top on the Cabriolet model, the rear suspension geometry was changed for all models in 1991, which is important to know if you make any rear suspension upgrades. As a Digital Motor Electronics (DME)-based Porsche platform, 964-owners should consider carrying a spare DME relay (part no. 993.615.227.00, around $22) in your glove-box.

Copied from https://members.rennlist.com/jfk964/porsche_964_faq.htm
 
Hi David
Thanks for the couple of links, very useful. I have downloaded the Porsche workshop article and considering purchasing the DVD from Pfixit.
 
You must log in or register to reply here.

Posts made and opinions expressed are those of the individual forum members

Use of the Forum is subject to the Terms and Conditions

Disclaimer

The opinions expressed on this site are not necessarily those of the Club, who shall have no liability in respect of them or the accuracy of the content. The Club assumes no responsibility for any effects arising from errors or omissions.

Porsche Club Great Britain gives no warranties, guarantees or assurances and makes no representations or recommendations regarding any goods or services advertised on this site. It is the responsibility of visitors to satisfy themselves that goods and/or services supplied by any advertiser are bona fide and in no instance can the Porsche Club Great Britain be held responsible.

When responding to advertisements please ensure that you satisfy yourself of any applicable call charges on numbers not prefixed by usual "landline" STD Codes. Information can be obtained from the operator or the white pages. Before giving out ANY information regarding cars, or any other items for sale, please satisfy yourself that any potential purchaser is bona fide.

Directors of the Board of Porsche Club GB, Club Office Staff, Register Secretaries and Regional Organisers are often requested by Club members to provide information on matters connected with their cars and other matters referred to in the Club Rules. Such information, advice and assistance provided by such persons is given in good faith and is based on the personal experience and knowledge of the individual concerned.

Neither Porsche Club GB, nor any of the aforementioned, shall be under any liability in respect of any such information, advice or assistance given to members. Members are advised to consult qualified specialists for information, advice and assistance on matters connected with their cars at all times.

Porsche
Lockton
Pirelli
Officially approved
Oracle Finance
WEX Esso
Collecting Cars
Back
Top